Error Messages

Error Messages

The following table lists messages that can appear in system log files. This list is not exhaustive; it describes warning messages that can occur and might require your attention. For information about warning messages not included in the list below, go to www.websense.com and then navigate to Support and Knowledge Base.

Process fatal errors


Message	Description
Accept port is not between 1 and 65535. Please check configuration.	The port specified in the records.config file that accepts incoming HTTP requests is not valid.
Ftp accept port is not between 1 and 65535.	The port specified in the records.config file that accepts incoming FTP requests is not valid.
Self loop is detected in parent proxy configuration.	The name and port of the parent proxy are the same as that of Content Gateway. This creates a loop when Content Gateway attempts to send requests to the parent proxy.
Could not open the ARM device	The ARM failed to load. The most common reason for this is that the host system has an incompatible system kernel. To see if the ARM is loaded, run: /sbin/lsmod \| grep arm
content_manager failed to set cluster IP address	The content_manager process could not set the cluster IP address. Check the cluster IP address. Make sure that it is not already used by another device in the network.
Unable to initialize storage. (Re)Configuration required.	Cache initialization failed during startup. The cache configuration should be checked and configured or reconfigured.

Warnings


Message	Description
Logfile error: error_number	Generic logging error.
Bad cluster major version range version1-version2 for node IP address connect failed	Incompatible software versions causing a problem.
can't open config file filename for reading custom formats	Custom logging is enabled, but Content Gateway cannot find the logs.config file.
connect by disallowed client IP address, closing connection	The specified client is not allowed to connect to Content Gateway. The client IP address is not listed in the ip_allow.config file.
Could not rename log filename to rolled filename	System error when renaming log file during roll.
Did this_amount of backup still to do remaining_amount	Congestion is approaching.
Different clustering minor versions version 1, version 2 for node IP address continuing	Incompatible software versions causing a problem.
log format symbol symbol_name not found	Custom log format references a field symbol that does not exist. See Event Logging Formats.
missing field for field marker	Error reading a log buffer.
Unable to accept cluster connections on port: cluster_port_number	Contact Websense Technical Support. Go to www.websense.com/support/ for Technical Support contact information
Unable to open log file filename, errno=error_number	Cannot open the log file.
Error accessing disk disk_name	Content Gateway might have a cache read problem. You might have to replace the disk.
Too many errors accessing disk disk_name: declaring disk bad	Content Gateway is not using the cache disk because it encountered too many errors. The disk might be corrupt and might have to be replaced.
No cache disks specified in storage.config file: cache disabled	The Content Gateway storage.config file does not list any cache disks. Content Gateway is running in proxy-only mode. You must add the disks you want to use for the cache to the storage.config file (see storage.config).
All disks are bad, cache disabled	There is a problem with the cache disk(s) and caching has been disabled. Please verify that the cache disks are working and have been properly formatted for caching. See Configuring the Cache.
Missing DC parameter <missing_param> on auth.profile line	A required parameter was not specified. Please provide a value for the missing parameter.
Bad DC parameter <bad_param> - <dc_name>	A specified Domain Controller parameter is invalid. Please enter a valid value for the cited parameter.
[ParentSelection] <error_description> for default parent proxy	Proxy chaining is not working due to misconfiguration of the parent proxy in the child proxy. Please check the chaining configuration of parent proxy values in the child proxy.
WCCP2: Cannot find Interface name. Please check that the variable proxy.local.wccp2. ethernet_interface is set correctly	No value is specified for the WCCP interface. In Content Gateway Manager check Configure > Networking > WCCP > General. Or assign a value to proxy.local.wccp2.ethernet_interface in records.config.
ARMManager: Unable to read network interface configuration	There is a format or configuration error in ipnat.conf. In Content Gateway Manager, go to Configure > Networking > ARM > General and click Edit File to view and correct ipnat.conf.

Error Messages

Support

Search

Article Rating:

Related Articles

Quick Links

Service Requests

How are we doing?